Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
The article author is making a number of great points relating to A Step-by-Step Guide to Installing a Bathtub overall in the article followed below.
Installing a tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging project. If the old bathtub is conveniently accessible, the task can move rapidly; if you have to open up a wall surface to get rid of the old tub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub and also set in the brand-new one. Make sure you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a professional to take control of a halfway-completed project, it is better to consider employing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your restroom if you have already purchased a new tub and don't need to change the setup of your previous water supply pipelines.
Your devices and also product list must make up the following:
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the restricted gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will come from the pipelines. Once the supply pipelines have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the supply of water and check all joints and new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been utilized a minimum of once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Safeguard the tap in position with the maker offered backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former kind should be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about complications with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post on Tools You Need to Install a New Bathtub . Thank you so much for taking the time to read our blog. Loved our article? Please share it. Let someone else discover it. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Quote & Schedule Report this page